Booster Installation

Description
A FileWave Booster can run on macOS, Windows, or Debian. Installers, appliances, and current install commands are on FileWave Software Downloads.
Installers
Debian
Debian has two options. FileWave provides a pre-built Debian VM, similar to the FileWave Server appliance, or you can self-install the Booster software on a Debian system.
macOS & Windows
Installers are available as PKG or MSI.
The Windows MSI can install, repair, or remove the Booster software.
Install Paths
Booster installs the software to one of the following locations:
Windows: C:\Program Files\FileWave\fwBooster.exe
macOS, Debian: /usr/local/sbin/fwBooster
Booster Configuration
Once installed, configuration is via the Booster Monitor application, available for both macOS and Windows from the same downloads page.
Note that the standalone application, Booster Monitor, will only be able to connect to a Booster for initial configuration. Once a Booster is configured you must access Booster Monitor from FileWave Central in the Boosters section. This is because authentication is protected, and the FileWave Central application provides a secure connection. Launching Booster Monitor directly would not have that same authentication, and you will see an error about the Booster not running.
Installation
Debian
If using the pre-built Debian Appliance, simply add the VM to the VM infrastructure.  Alternatively, follow the commands provided on the downloads page.
macOS & Windows
Run the relevant PKG or MSI installer, accepting any terms and agreements.
Custom Installers may be created, pre-defining details, e.g. Server Address, Port and Booster Monitor Preferences password: Custom Installers
Configuration
Network Address
Configure a static IP for the Booster and consider adding a Domain Name within the DNS for this IP.
macOS and Windows Boosters can be configured through Settings. Debian Boosters require command-line network configuration.
Debian IP Setup
Network Interface
The current IP may be determined with the 'ip addr' command:
# ip addr
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host noprefixroute 
       valid_lft forever preferred_lft forever
2: ens192: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc mq state UP group default qlen 1000
    link/ether 00:0c:29:9d:4d:7e brd ff:ff:ff:ff:ff:ff
    altname enp11s0
    inet 192.168.1.98/24 brd 192.168.1.255 scope global dynamic ens192
       valid_lft 68853sec preferred_lft 68853sec
    inet6 fe80::20c:29ff:fe9d:4d7e/64 scope link 
       valid_lft forever preferred_lft forever
The key part here is the name of the network interface.  In the above example, this is 'ens192'.
Edit Network File
Make a backup of the current file:
cp /etc/network/interfaces /etc/network/interfaces-mybackup
Edit the original file:
sudo nano /etc/network/interfaces
Add the chosen IP and other necessary details for this interface.  Given the details above, it may look something like the below once edited:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
source /etc/network/interfaces.d/*
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
iface ens192 inet static
address 192.168.1.22
netmask 255.255.255.0
gateway 192.168.1.255
dns-nameservers 8.8.4.4 8.8.8.8
Once complete, save and then restart the network service:
sudo systemctl restart networking
Re-running the 'ip addr' command should now show the new details.
Add a name with this IP on the DNS.
Booster Setup
Install Booster Monitor on a macOS or Windows device. When you launch Booster Monitor, connect to the network address you created for the Booster. The initial view is similar to FileWave Client Monitor, but it shows Booster-specific details:
Select Preferences, then enter the password you created, or the default password from the Downloads page.
Change the default Booster Monitor password during setup.
This password is only used to access the Preferences from the Booster Monitor.
The Booster Monitor may then be used to configure the Booster.  At a very basic level, the Server Address and port should be added.
Approving Boosters
Once a Booster is setup on the network with the relevant FileWave Server details, it should then check-in with the server and be visible in the Booster section of the FileWave Central admin application software.
Current Boosters use certificate-based approval before the FileWave Server trusts them.
The approval process generates a certificate for the Booster.  There are four ways to generate a certificate for a booster.
Select booster(s) in the Booster view → right-click → Create Certificate/Enroll Booster
Select booster(s) in the Booster view → Create Certificate/Enroll Booster (in the button bar)
Select booster(s) in the Booster Details → right-click → Create Certificate/Enroll Booster
Select booster(s) in the Booster Details → Create Certificate/Enroll Booster (in the button bar)
Booster Deletion
If you delete a Booster from FileWave, FileWave revokes its certificate. If the Booster is still running, it must be approved again after its next check-in.